commit 716b2edd7a8d4286dd026ecc9befb45b94893240 Author: Peter Tillemans Date: Mon May 26 14:17:25 2025 +0200 initial commit diff --git a/.gitignore b/.gitignore new file mode 100644 index 0000000..5bfd5aa --- /dev/null +++ b/.gitignore @@ -0,0 +1,3 @@ +printer-*_*.cfg +.moonraker.conf.bkp +raspinfo.txt diff --git a/crowsnest.conf b/crowsnest.conf new file mode 100644 index 0000000..3176ace --- /dev/null +++ b/crowsnest.conf @@ -0,0 +1,47 @@ +#### crowsnest.conf +#### This is a typical default config. +#### Also used as default in mainsail / MainsailOS +#### See: +#### https://github.com/mainsail-crew/crowsnest/blob/master/README.md +#### for details to configure to your needs. + + +##################################################################### +#### ##### +#### Information about ports and according URL's ##### +#### ##### +##################################################################### +#### ##### +#### Port 8080 equals /webcam/?action=[stream/snapshot] ##### +#### Port 8081 equals /webcam2/?action=[stream/snapshot] ##### +#### Port 8082 equals /webcam3/?action=[stream/snapshot] ##### +#### Port 8083 equals /webcam4/?action=[stream/snapshot] ##### +#### ##### +#### Note: These ports are default for most Mainsail ##### +#### installations. To use any other port would involve ##### +#### changing the proxy configuration or using directly ##### +#### http://:/?action=[stream/snapshot] ##### +#### ##### +##################################################################### +#### RTSP Stream URL: ( if enabled and supported ) ##### +#### rtsp://:/stream.h264 ##### +##################################################################### + + +[crowsnest] +log_path: /home/pti/printer_data/logs/crowsnest.log +log_level: verbose # Valid Options are quiet/verbose/debug +delete_log: false # Deletes log on every restart, if set to true +no_proxy: false + +[cam 1] +mode: ustreamer # ustreamer - Provides mjpg and snapshots. (All devices) + # camera-streamer - Provides webrtc, mjpg and snapshots. (rpi + Raspi OS based only) +enable_rtsp: false # If camera-streamer is used, this enables also usage of an rtsp server +rtsp_port: 8554 # Set different ports for each device! +port: 8080 # HTTP/MJPG Stream/Snapshot Port +device: /dev/video0 # See Log for available ... +resolution: 640x480 # widthxheight format +max_fps: 15 # If Hardware Supports this it will be forced, otherwise ignored/coerced. +#custom_flags: # You can run the Stream Services with custom flags. +#v4l2ctl: # Add v4l2-ctl parameters to setup your camera, see Log what your cam is capable of. diff --git a/mainsail.cfg b/mainsail.cfg new file mode 120000 index 0000000..8e52424 --- /dev/null +++ b/mainsail.cfg @@ -0,0 +1 @@ +/home/pti/mainsail-config/mainsail.cfg \ No newline at end of file diff --git a/moonraker.conf b/moonraker.conf new file mode 100644 index 0000000..19daea2 --- /dev/null +++ b/moonraker.conf @@ -0,0 +1,90 @@ +[server] +host: 0.0.0.0 +port: 7125 +# The maximum size allowed for a file upload (in MiB). Default 1024 MiB +max_upload_size: 1024 +# Path to klippy Unix Domain Socket +klippy_uds_address: ~/printer_data/comms/klippy.sock + +[file_manager] +# post processing for object cancel. Not recommended for low resource SBCs such as a Pi Zero. Default False +enable_object_processing: False + +[authorization] +cors_domains: + https://my.mainsail.xyz + http://my.mainsail.xyz + http://*.local + http://*.lan +trusted_clients: + 10.0.0.0/8 + 127.0.0.0/8 + 169.254.0.0/16 + 172.16.0.0/12 + 192.168.0.0/16 + FE80::/10 + ::1/128 + +# enables partial support of Octoprint API +[octoprint_compat] + +# enables moonraker to track and store print history. +[history] + +# this enables moonraker announcements for mainsail +[announcements] +subscriptions: + mainsail + +# this enables moonraker's update manager +[update_manager] +refresh_interval: 168 +enable_auto_refresh: True + +[update_manager mainsail] +type: web +channel: stable +repo: mainsail-crew/mainsail +path: ~/mainsail + +[update_manager mainsail-config] +type: git_repo +primary_branch: master +path: ~/mainsail-config +origin: https://github.com/mainsail-crew/mainsail-config.git +managed_services: klipper + +### moonraker-timelapse +### Don't forget to include timelapse.cfg to your printer.cfg +### Uncomment to enable moonraker-timelapse + + +#[update_manager timelapse] +#type: git_repo +#primary_branch: main +#path: ~/moonraker-timelapse +#origin: https://github.com/mainsail-crew/moonraker-timelapse.git +#managed_services: klipper moonraker + +#[timelapse] +### Directory where the generated video will be saved +#output_path: ~/timelapse/ +### Directory where ffmpeg is installed +#ffmpeg_binary_path: /usr/bin/ffmpeg + +# Crowsnest update_manager entry +[update_manager crowsnest] +type: git_repo +path: ~/crowsnest +origin: https://github.com/mainsail-crew/crowsnest.git +managed_services: crowsnest +install_script: tools/pkglist.sh + +# Sonar update_manager entry +[update_manager sonar] +type: git_repo +path: ~/sonar +origin: https://github.com/mainsail-crew/sonar.git +primary_branch: main +managed_services: sonar +install_script: tools/install.sh diff --git a/printer.cfg b/printer.cfg new file mode 100644 index 0000000..be593b6 --- /dev/null +++ b/printer.cfg @@ -0,0 +1,647 @@ +#nDesign VORON2 250/300/350mm SKR 1.3 TMC2209 UART config + +## *** THINGS TO CHANGE/CHECK: *** +## MCU paths [mcu] section +## Thermistor types [extruder] and [heater_bed] sections - See https://www.klipper3d.org/Config_Reference.html#common-thermistors for common thermistor types +## Z Endstop Switch location [safe_z_home] section +## Homing end position [gcode_macro G32] section +## Z Endstop Switch offset for Z0 [stepper_z] section +## Probe points [quad_gantry_level] section +## Min & Max gantry corner postions [quad_gantry_level] section +## PID tune [extruder] and [heater_bed] sections +## Fine tune E steps [extruder] section + +##========================== Pin Definitions ======================== +## X_STEP_PIN 2.2 +## X_DIR_PIN 2.6 +## X_ENABLE_PIN 2.1 +## X_MIN_PIN 1.29 +## X_MAX_PIN 1.28 +## X_UART_RX 1.17 +## X_UART_TX 4.29 + +## Y_STEP_PIN 0.19 +## Y_DIR_PIN 0.20 +## Y_ENABLE_PIN 2.8 +## Y_MIN_PIN 1.27 +## Y_MAX_PIN 1.26 +## Y_UART_RX 1.15 +## Y_UART_TX 1.16 + +## Z_STEP_PIN 0.22 +## Z_DIR_PIN 2.11 +## Z_ENABLE_PIN 0.21 +## Z_MIN_PIN 1.25 +## Z_MAX_PIN 1.24 +## Z_UART_RX 1.10 +## Z_UART_TX 1.14 + +## E0_STEP_PIN 2.13 +## E0_DIR_PIN 0.11 +## E0_ENABLE_PIN 2.12 +## E0_UART_RX 1.8 +## E0_UART_TX 1.9 + +## E1_STEP_PIN 0.1 +## E1_DIR_PIN 0.0 +## E1_ENABLE_PIN 0.10 +## E1_UART_RX 1.1 +## E1_UART_TX 1.4 + +## HE1 2.4 +## HE0 2.7 +## BED 2.5 +## TH1 (H1 Temp) 0.25 +## TH0 (H0 Temp) 0.24 +## TB (Bed Temp) 0.23 +## FAN 2.3 +## SERVO 2.0 +##=================================================================== + +## include mainsail config +[include mainsail.cfg] + +## MCU for X/Y/E steppers main MCU +## [X in X] - B Motor +## [Y in Y] - A Motor +## [E in E0] - Extruder +[mcu] +## Obtain definition by "ls /dev/serial/by-id/*" then unplug to verify +##-------------------------------------------------------------------- +serial: /dev/serial/by-id/usb-Klipper_lpc1768_22B00012658C48AFD115345DC12000F5-if00 +##-------------------------------------------------------------------- + +## MCU for Z steppers +## [Z in X] - Front Left +## [Z1 in Y] - Rear Left +## [Z2 in Z] - Rear Right +## [Z3 in E0]- Front Right +[mcu z] +## Obtain definition by "ls /dev/serial/by-id/*" then unplug to verify +##-------------------------------------------------------------------- +serial: /dev/serial/by-id/usb-Klipper_lpc1768_0260000E648C48AF0B98335DC12000F5-if00 +##-------------------------------------------------------------------- + +[printer] +kinematics: corexy +max_velocity: 300 +max_accel: 7000 #Max 4000 +max_z_velocity: 15 #Max 15 for 12V TMC Drivers, can increase for 24V +max_z_accel: 350 +square_corner_velocity: 5.0 + +##################################################################### +# X/Y Stepper Settings +##################################################################### + +## Connected to X on mcu_xye (B Motor) +[stepper_x] +step_pin: P2.2 +dir_pin: !P2.6 +enable_pin: !P2.1 +rotation_distance: 40 +microsteps: 32 +full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper +endstop_pin: P1.28 +position_min: 0 +##-------------------------------------------------------------------- + +## Uncomment below for 250mm build +#position_endstop: 250 +#position_max: 250 + +## Uncomment for 300mm build +#position_endstop: 300 +#position_max: 300 + +## Uncomment for 350mm build +position_endstop: 350 +position_max: 350 + +##-------------------------------------------------------------------- +homing_speed: 25 #Max 100 +homing_retract_dist: 5 +homing_positive_dir: true + +## Make sure to update below for your relevant driver (2208 or 2209) +[tmc2209 stepper_x] +uart_pin: P1.17 +interpolate: False +run_current: 0.8 +sense_resistor: 0.110 +stealthchop_threshold: 0 + +## Connected to Y on mcu_xye (A Motor) +[stepper_y] +step_pin: P0.19 +dir_pin: !P0.20 +enable_pin: !P2.8 +rotation_distance: 40 +microsteps: 32 +full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper +endstop_pin: P1.26 +position_min: 0 +##-------------------------------------------------------------------- + +## Uncomment for 250mm build +#position_endstop: 250 +#position_max: 250 + +## Uncomment for 300mm build +#position_endstop: 300 +#position_max: 300 + +## Uncomment for 350mm build +position_endstop: 350 +position_max: 350 + +##-------------------------------------------------------------------- +homing_speed: 25 #Max 100 +homing_retract_dist: 5 +homing_positive_dir: true + +## Make sure to update below for your relevant driver (2208 or 2209) +[tmc2209 stepper_y] +uart_pin: P1.15 +interpolate: False +run_current: 0.8 +sense_resistor: 0.110 +stealthchop_threshold: 0 + +##################################################################### +# Z Stepper Settings +##################################################################### + +## Z MCU - In X Position +## Z0 Stepper - Front Left +[stepper_z] +step_pin: z:P2.2 +dir_pin: !z:P2.6 +enable_pin: !z:P2.1 +rotation_distance: 40 +gear_ratio: 80:16 +microsteps: 32 +endstop_pin: z:P1.25 +## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0) +## (+) value = endstop above Z0, (-) value = endstop below +## Increasing position_endstop brings nozzle closer to the bed +## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config +#position_endstop = -1.436 +##-------------------------------------------------------------------- + +## Uncomment below for 250mm build +#position_max: 210 + +## Uncomment below for 300mm build +#position_max: 260 + +## Uncomment below for 350mm build +position_max: 310 + +##-------------------------------------------------------------------- +position_min: -5 +homing_speed: 8 +second_homing_speed: 3 +homing_retract_dist: 3 + +## Make sure to update below for your relevant driver (2208 or 2209) +[tmc2209 stepper_z] +uart_pin: z:P1.17 +interpolate: False +run_current: 0.8 +sense_resistor: 0.110 +stealthchop_threshold: 0 + +## Z MCU - In Y Position +## Z1 Stepper - Rear Left +[stepper_z1] +step_pin: z:P0.19 +dir_pin: z:P0.20 +enable_pin: !z:P2.8 +rotation_distance: 40 +gear_ratio: 80:16 +microsteps: 32 + +## Make sure to update below for your relevant driver (2208 or 2209) +[tmc2209 stepper_z1] +uart_pin: z:P1.15 +interpolate: False +run_current: 0.8 +sense_resistor: 0.110 +stealthchop_threshold: 0 + +## Z MCU - In Z Position +## Z2 Stepper - Rear Right +[stepper_z2] +step_pin: z:P0.22 +dir_pin: !z:P2.11 +enable_pin: !z:P0.21 +rotation_distance: 40 +gear_ratio: 80:16 +microsteps: 32 + +## Make sure to update below for your relevant driver (2208 or 2209) +[tmc2209 stepper_z2] +uart_pin: z:P1.10 +interpolate: False +run_current: 0.8 +sense_resistor: 0.110 +stealthchop_threshold: 0 + +## Z MCU - In E0 Position +## Z3 Stepper - Front Right +[stepper_z3] +step_pin: z:P2.13 +dir_pin: z:P0.11 +enable_pin: !z:P2.12 +rotation_distance: 40 +gear_ratio: 80:16 +microsteps: 32 + +## Make sure to update below for your relevant driver (2208 or 2209) +[tmc2209 stepper_z3] +uart_pin: z:P1.8 +interpolate: False +run_current: 0.8 +sense_resistor: 0.110 +stealthchop_threshold: 0 + + +##################################################################### +# Extruder +##################################################################### + +# E0 on MCU X/Y +[extruder] +step_pin: P2.13 +dir_pin: P0.11 +enable_pin: !P2.12 +## Update value below when you perform extruder calibration +## If you ask for 100mm of filament, but in reality it is 98mm: +## rotation_distance = * / 100 +## 22.6789511 is a good starting point +rotation_distance: 22.6789511 #Bondtech 5mm Drive Gears +## Update Gear Ratio depending on your Extruder Type +## Use 50:10 for Stealthburner/Clockwork 2 +## Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio) +## Use 80:20 for M4, M3.1 +gear_ratio: 50:17 +microsteps: 32 +full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree +nozzle_diameter: 0.400 +filament_diameter: 1.75 +heater_pin: P2.7 +## Check what thermistor type you have. See https://www.klipper3d.org/Config_Reference.html#common-thermistors for common thermistor types. +## Use "Generic 3950" for NTC 100k 3950 thermistors +sensor_type: Generic 3950 +sensor_pin: P0.24 +min_temp: 10 +max_temp: 270 +max_power: 1.0 +min_extrude_temp: 170 +control = pid +pid_kp = 22.780 +pid_ki = 1.298 +pid_kd = 99.947 + +## Try to keep pressure_advance below 1.0 +#pressure_advance: 0.05 +## Default is 0.040, leave stock +#pressure_advance_smooth_time: 0.040 + +## E0 on MCU X/Y +## Make sure to update below for your relevant driver (2208 or 2209) +[tmc2209 extruder] +uart_pin: P1.9 +interpolate: false +run_current: 0.5 +sense_resistor: 0.110 +stealthchop_threshold: 0 + +##################################################################### +# Bed Heater +##################################################################### + +## SSR Pin - Z board, Fan Pin +[heater_bed] +heater_pin: z:P2.3 +## Check what thermistor type you have. See https://www.klipper3d.org/Config_Reference.html#common-thermistors for common thermistor types. +## Use "Generic 3950" for Keenovo heaters +sensor_type: Generic 3950 +sensor_pin: z:P0.23 +pullup_resistor: 6000 +## Adjust max_power so it doesn't exceed the SSR rating. The Omron G3NA-210B-DC5 SSR is rated at 4 amps without a heatsink. +## The formula is "4 / (Wattage_of_bed_heater / Mains_voltage) = max_power" +## If max_power is greater than 1.0, use 1.0 +max_power: 0.6 +min_temp: 0 +max_temp: 120 +control = pid +pid_kp = 39.695 +pid_ki = 1.478 +pid_kd = 266.452 + +##################################################################### +# Probe +##################################################################### +## Inductive Probe +## This probe is not used for Z height, only Quad Gantry Leveling +## Z_MAX on mcu_z +## If your probe is NO instead of NC, add change pin to !z:P1.24 +[probe] +pin: z:P1.24 +x_offset: 0 +y_offset: 25.0 +z_offset: 2.400 +speed: 10.0 +samples: 3 +samples_result: median +sample_retract_dist: 3.0 +samples_tolerance: 0.006 +samples_tolerance_retries: 3 + +##################################################################### +# Fan Control +##################################################################### + +## Hotend Fan - XYE board, HE1 Connector +[heater_fan hotend_fan] +pin: P2.4 +max_power: 0.5 +shutdown_speed: 0 +kick_start_time: 0.5 +heater: extruder +heater_temp: 50.0 +## If you are experiencing back flow, you can reduce fan_speed +#fan_speed: 1.0 + +## Print Cooling Fan - XYE board, Fan Pin +[fan] +pin: P2.3 +max_power: 1.0 +shutdown_speed: 0 +kick_start_time: 0.5 +## Depending on your fan, you may need to increase this value +## if your fan will not start. Can change cycle_time (increase) +## if your fan is not able to slow down effectively +off_below: 0.10 + + +## Controller fan - Z board, HE1 Connector +[heater_fan controller_fan] +pin: z:P2.4 +max_power: 0.25 +shutdown_speed: 0 +kick_start_time: 0.5 +heater: heater_bed +heater_temp: 45.0 + +## Exhaust fan - Z board, HE0 Connector +[heater_fan exhaust_fan] +pin: z:P2.7 +max_power: 0.5 +shutdown_speed: 0.0 +kick_start_time: 5.0 +heater: heater_bed +heater_temp: 80 +fan_speed: 1.0 + +##################################################################### +# LED Control +##################################################################### + +# Chamber Lighting - Bed Connector (Optional) +#[output_pin caselight] +#pin: P2.5 +#pwm:true +#shutdown_value: 0 +#value:1 +#cycle_time: 0.01 + +##################################################################### +# Homing and Gantry Adjustment Routines +##################################################################### + +[idle_timeout] +timeout: 1800 + +[safe_z_home] +## XY Location of the Z Endstop Switch +## Update -10,-10 to the XY coordinates of your endstop pin +## (such as 157,305) after going through Z Endstop Pin +## Location Definition step. +home_xy_position: 234,350 +speed:100 +z_hop:10 + + +## Use QUAD_GANTRY_LEVEL to level a gantry. +## Min & Max gantry corners - measure from nozzle at MIN (0,0) and +## MAX (250, 250), (300,300), or (350,350) depending on your printer size +## to respective belt positions +[quad_gantry_level] +#-------------------------------------------------------------------- +## Gantry Corners for 250mm Build +## Uncomment for 250mm build +#gantry_corners: +# -60,-10 +# 310, 320 +## Probe points +#points: +# 50,25 +# 50,175 +# 200,175 +# 200,25 + +## Gantry Corners for 300mm Build +## Uncomment for 300mm build +#gantry_corners: +# -60,-10 +# 360,370 +## Probe points +#points: +# 50,25 +# 50,225 +# 250,225 +# 250,25 + +## Gantry Corners for 350mm Build +## Uncomment for 350mm build +gantry_corners: + -60,-10 + 410,420 +## Probe points +points: + 50,25 + 50,275 + 300,275 + 300,25 + +#-------------------------------------------------------------------- +speed: 100 +horizontal_move_z: 10 +retries: 5 +retry_tolerance: 0.0075 +max_adjust: 15 + +##################################################################### +# Displays +##################################################################### + +## Uncomment the display that you have. Display connects to Z MCU +#-------------------------------------------------------------------- + +## RepRapDiscount 128x64 Full Graphic Smart Controller +#[display] +#lcd_type: st7920 +#cs_pin: z:P1.19 +#sclk_pin: z:P1.20 +#sid_pin: z:P1.18 +#menu_timeout: 40 +#encoder_pins: ^z:P3.26, ^z:P3.25 +#click_pin: ^!z:P0.28 + +#[output_pin beeper] +#pin: z:P1.30 + +#-------------------------------------------------------------------- + +## mini12864 LCD Display +[display] +lcd_type: uc1701 +cs_pin: z:P1.18 +a0_pin: z:P1.19 +encoder_pins: ^z:P3.25,^z:P3.26 +click_pin: ^!z:P0.28 +contrast: 56 + +## To control Neopixel RGB in mini12864 display +[neopixel fysetc_mini12864] +pin: z:P1.21 +chain_count: 3 +initial_RED: 0.1 +initial_GREEN: 0.5 +initial_BLUE: 0.2 +color_order: RGB + +## Set RGB values on boot up for each Neopixel. +## Index 1 = display, Index 2 and 3 = Knob + +[delayed_gcode setdisplayneopixel] +initial_duration: 1 +gcode: + SET_LED LED=fysetc_mini12864 RED=1 GREEN=1 BLUE=1 INDEX=1 TRANSMIT=0 + SET_LED LED=fysetc_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=2 TRANSMIT=0 + SET_LED LED=fysetc_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=3 + +#-------------------------------------------------------------------- + + +##################################################################### +# Macros +##################################################################### +[gcode_macro PARK] +gcode: + {% set th = printer.toolhead %} + G0 X{th.axis_maximum.x//2} Y{th.axis_maximum.y//5} Z100 + +[gcode_macro G32] +gcode: + SAVE_GCODE_STATE NAME=STATE_G32 + G90 + G28 + QUAD_GANTRY_LEVEL + G28 + PARK + RESTORE_GCODE_STATE NAME=STATE_G32 + +[gcode_macro PRINT_START] +# Use PRINT_START for the slicer starting script - please customise for your slicer of choice +gcode: + G32 ; home all axes + G90 ; absolute positioning + G1 Z20 F3000 ; move nozzle away from bed + SFS_ENABLE + + +[gcode_macro PRINT_END] +# Use PRINT_END for the slicer ending script - please customise for your slicer of choice +gcode: + # safe anti-stringing move coords + {% set th = printer.toolhead %} + {% set x_safe = th.position.x + 20 * (1 if th.axis_maximum.x - th.position.x > 20 else -1) %} + {% set y_safe = th.position.y + 20 * (1 if th.axis_maximum.y - th.position.y > 20 else -1) %} + {% set z_safe = [th.position.z + 2, th.axis_maximum.z]|min %} + + SAVE_GCODE_STATE NAME=STATE_PRINT_END + + M400 ; wait for buffer to clear + G92 E0 ; zero the extruder + G1 E-5.0 F1800 ; retract filament + + TURN_OFF_HEATERS + + SFS_DISABLE + + G90 ; absolute positioning + G0 X{x_safe} Y{y_safe} Z{z_safe} F20000 ; move nozzle to remove stringing + G0 X{th.axis_maximum.x//2} Y{th.axis_maximum.y - 2} F3600 ; park nozzle at rear + M107 ; turn off fan + + BED_MESH_CLEAR + + # The purpose of the SAVE_GCODE_STATE/RESTORE_GCODE_STATE + # command pair is to restore the printer's coordinate system + # and speed settings since the commands above change them. + # However, to prevent any accidental, unintentional toolhead + # moves when restoring the state, explicitly set MOVE=0. + RESTORE_GCODE_STATE NAME=STATE_PRINT_END MOVE=0 + + +[input_shaper] +shaper_freq_x: 46.08 # frequency for the X mark of the test model +shaper_freq_y: 40.16 # frequency for the Y mark of the test model +shaper_type: mzv # first recommended shaper + + +[bed_mesh] +speed: 120 +horizontal_move_z: 5 +mesh_min: 25, 25 +mesh_max: 325, 325 +probe_count: 6, 6 + +[filament_motion_sensor SFS_T0] +detection_length: 10.00 ; This can be adjusted to your desired level of sensitivity. 10 is a recommended value to prevent flow dropoff false triggers. +extruder: extruder +switch_pin: ^P1.27 +pause_on_runout: True ; This can be set to false to debug false positives putting the sensor in "monitor mode". The printer will not pause but it will run the runout_gcode below. +event_delay: 3.0 +pause_delay: 0.5 +runout_gcode: + M117 Runout Detected! + +[delayed_gcode DISABLEFILAMENTSENSOR] ; This will disable the SFS 1 second after klipper starts +initial_duration: 1 +gcode: + SET_FILAMENT_SENSOR SENSOR=SFS_T0 ENABLE=0 ; Put your filament sensor's name after SENSOR= + +[gcode_macro SFS_ENABLE] ; Add this to PRINT_START +description: Enable smart filament sensor +gcode: + M117 ENABLING the Smart Filament Sensor + G92 E0 + SET_FILAMENT_SENSOR SENSOR=SFS_T0 ENABLE=1 ; Put your filament sensor's name after SENSOR= + +[gcode_macro SFS_DISABLE] ; Add this to PRINT_END and PRINT_CANCEL +description: Disable smart filament sensor +gcode: + M117 DISABLING the Smart Filament Sensor + G92 E0 + SET_FILAMENT_SENSOR SENSOR=SFS_T0 ENABLE=0 ; Put your filament sensor's name after SENSOR= + +#*# <---------------------- SAVE_CONFIG ----------------------> +#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. +#*# +#*# [stepper_z] +#*# position_endstop = -1.410 diff --git a/sonar.conf b/sonar.conf new file mode 100644 index 0000000..0c71ab1 --- /dev/null +++ b/sonar.conf @@ -0,0 +1,17 @@ +#### Sonar - A WiFi Keepalive daemon +#### +#### Written by Stephan Wendel aka KwadFan +#### Copyright 2022 +#### https://github.com/mainsail-crew/sonar +#### +#### This File is distributed under GPLv3 +#### + +[sonar] +enable: false # false to disable till next reboot (will stop again if not set to true) +debug_log: false # if set to true, sonar will log ever ping with triptime and date/time +persistant_log: false # If true logs in /var/log/sonar.log, false logs to systemd +target: auto # IP Address, URL or auto as ping target +count: 3 # How often should be pinged? +interval: 60 # Ping again after X seconds +restart_treshold: 10 # If failed, restart WiFi after X seconds diff --git a/timelapse.cfg b/timelapse.cfg new file mode 120000 index 0000000..93885db --- /dev/null +++ b/timelapse.cfg @@ -0,0 +1 @@ +/home/pti/moonraker-timelapse/klipper_macro/timelapse.cfg \ No newline at end of file