647 lines
18 KiB
INI
647 lines
18 KiB
INI
#nDesign VORON2 250/300/350mm SKR 1.3 TMC2209 UART config
|
|
|
|
## *** THINGS TO CHANGE/CHECK: ***
|
|
## MCU paths [mcu] section
|
|
## Thermistor types [extruder] and [heater_bed] sections - See https://www.klipper3d.org/Config_Reference.html#common-thermistors for common thermistor types
|
|
## Z Endstop Switch location [safe_z_home] section
|
|
## Homing end position [gcode_macro G32] section
|
|
## Z Endstop Switch offset for Z0 [stepper_z] section
|
|
## Probe points [quad_gantry_level] section
|
|
## Min & Max gantry corner postions [quad_gantry_level] section
|
|
## PID tune [extruder] and [heater_bed] sections
|
|
## Fine tune E steps [extruder] section
|
|
|
|
##========================== Pin Definitions ========================
|
|
## X_STEP_PIN 2.2
|
|
## X_DIR_PIN 2.6
|
|
## X_ENABLE_PIN 2.1
|
|
## X_MIN_PIN 1.29
|
|
## X_MAX_PIN 1.28
|
|
## X_UART_RX 1.17
|
|
## X_UART_TX 4.29
|
|
|
|
## Y_STEP_PIN 0.19
|
|
## Y_DIR_PIN 0.20
|
|
## Y_ENABLE_PIN 2.8
|
|
## Y_MIN_PIN 1.27
|
|
## Y_MAX_PIN 1.26
|
|
## Y_UART_RX 1.15
|
|
## Y_UART_TX 1.16
|
|
|
|
## Z_STEP_PIN 0.22
|
|
## Z_DIR_PIN 2.11
|
|
## Z_ENABLE_PIN 0.21
|
|
## Z_MIN_PIN 1.25
|
|
## Z_MAX_PIN 1.24
|
|
## Z_UART_RX 1.10
|
|
## Z_UART_TX 1.14
|
|
|
|
## E0_STEP_PIN 2.13
|
|
## E0_DIR_PIN 0.11
|
|
## E0_ENABLE_PIN 2.12
|
|
## E0_UART_RX 1.8
|
|
## E0_UART_TX 1.9
|
|
|
|
## E1_STEP_PIN 0.1
|
|
## E1_DIR_PIN 0.0
|
|
## E1_ENABLE_PIN 0.10
|
|
## E1_UART_RX 1.1
|
|
## E1_UART_TX 1.4
|
|
|
|
## HE1 2.4
|
|
## HE0 2.7
|
|
## BED 2.5
|
|
## TH1 (H1 Temp) 0.25
|
|
## TH0 (H0 Temp) 0.24
|
|
## TB (Bed Temp) 0.23
|
|
## FAN 2.3
|
|
## SERVO 2.0
|
|
##===================================================================
|
|
|
|
## include mainsail config
|
|
[include mainsail.cfg]
|
|
|
|
## MCU for X/Y/E steppers main MCU
|
|
## [X in X] - B Motor
|
|
## [Y in Y] - A Motor
|
|
## [E in E0] - Extruder
|
|
[mcu]
|
|
## Obtain definition by "ls /dev/serial/by-id/*" then unplug to verify
|
|
##--------------------------------------------------------------------
|
|
serial: /dev/serial/by-id/usb-Klipper_lpc1768_22B00012658C48AFD115345DC12000F5-if00
|
|
##--------------------------------------------------------------------
|
|
|
|
## MCU for Z steppers
|
|
## [Z in X] - Front Left
|
|
## [Z1 in Y] - Rear Left
|
|
## [Z2 in Z] - Rear Right
|
|
## [Z3 in E0]- Front Right
|
|
[mcu z]
|
|
## Obtain definition by "ls /dev/serial/by-id/*" then unplug to verify
|
|
##--------------------------------------------------------------------
|
|
serial: /dev/serial/by-id/usb-Klipper_lpc1768_0260000E648C48AF0B98335DC12000F5-if00
|
|
##--------------------------------------------------------------------
|
|
|
|
[printer]
|
|
kinematics: corexy
|
|
max_velocity: 300
|
|
max_accel: 7000 #Max 4000
|
|
max_z_velocity: 15 #Max 15 for 12V TMC Drivers, can increase for 24V
|
|
max_z_accel: 350
|
|
square_corner_velocity: 5.0
|
|
|
|
#####################################################################
|
|
# X/Y Stepper Settings
|
|
#####################################################################
|
|
|
|
## Connected to X on mcu_xye (B Motor)
|
|
[stepper_x]
|
|
step_pin: P2.2
|
|
dir_pin: !P2.6
|
|
enable_pin: !P2.1
|
|
rotation_distance: 40
|
|
microsteps: 32
|
|
full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper
|
|
endstop_pin: P1.28
|
|
position_min: 0
|
|
##--------------------------------------------------------------------
|
|
|
|
## Uncomment below for 250mm build
|
|
#position_endstop: 250
|
|
#position_max: 250
|
|
|
|
## Uncomment for 300mm build
|
|
#position_endstop: 300
|
|
#position_max: 300
|
|
|
|
## Uncomment for 350mm build
|
|
position_endstop: 350
|
|
position_max: 350
|
|
|
|
##--------------------------------------------------------------------
|
|
homing_speed: 25 #Max 100
|
|
homing_retract_dist: 5
|
|
homing_positive_dir: true
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_x]
|
|
uart_pin: P1.17
|
|
interpolate: False
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
## Connected to Y on mcu_xye (A Motor)
|
|
[stepper_y]
|
|
step_pin: P0.19
|
|
dir_pin: !P0.20
|
|
enable_pin: !P2.8
|
|
rotation_distance: 40
|
|
microsteps: 32
|
|
full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper
|
|
endstop_pin: P1.26
|
|
position_min: 0
|
|
##--------------------------------------------------------------------
|
|
|
|
## Uncomment for 250mm build
|
|
#position_endstop: 250
|
|
#position_max: 250
|
|
|
|
## Uncomment for 300mm build
|
|
#position_endstop: 300
|
|
#position_max: 300
|
|
|
|
## Uncomment for 350mm build
|
|
position_endstop: 350
|
|
position_max: 350
|
|
|
|
##--------------------------------------------------------------------
|
|
homing_speed: 25 #Max 100
|
|
homing_retract_dist: 5
|
|
homing_positive_dir: true
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_y]
|
|
uart_pin: P1.15
|
|
interpolate: False
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
#####################################################################
|
|
# Z Stepper Settings
|
|
#####################################################################
|
|
|
|
## Z MCU - In X Position
|
|
## Z0 Stepper - Front Left
|
|
[stepper_z]
|
|
step_pin: z:P2.2
|
|
dir_pin: !z:P2.6
|
|
enable_pin: !z:P2.1
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 32
|
|
endstop_pin: z:P1.25
|
|
## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0)
|
|
## (+) value = endstop above Z0, (-) value = endstop below
|
|
## Increasing position_endstop brings nozzle closer to the bed
|
|
## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config
|
|
#position_endstop = -1.436
|
|
##--------------------------------------------------------------------
|
|
|
|
## Uncomment below for 250mm build
|
|
#position_max: 210
|
|
|
|
## Uncomment below for 300mm build
|
|
#position_max: 260
|
|
|
|
## Uncomment below for 350mm build
|
|
position_max: 310
|
|
|
|
##--------------------------------------------------------------------
|
|
position_min: -5
|
|
homing_speed: 8
|
|
second_homing_speed: 3
|
|
homing_retract_dist: 3
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z]
|
|
uart_pin: z:P1.17
|
|
interpolate: False
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
## Z MCU - In Y Position
|
|
## Z1 Stepper - Rear Left
|
|
[stepper_z1]
|
|
step_pin: z:P0.19
|
|
dir_pin: z:P0.20
|
|
enable_pin: !z:P2.8
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 32
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z1]
|
|
uart_pin: z:P1.15
|
|
interpolate: False
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
## Z MCU - In Z Position
|
|
## Z2 Stepper - Rear Right
|
|
[stepper_z2]
|
|
step_pin: z:P0.22
|
|
dir_pin: !z:P2.11
|
|
enable_pin: !z:P0.21
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 32
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z2]
|
|
uart_pin: z:P1.10
|
|
interpolate: False
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
## Z MCU - In E0 Position
|
|
## Z3 Stepper - Front Right
|
|
[stepper_z3]
|
|
step_pin: z:P2.13
|
|
dir_pin: z:P0.11
|
|
enable_pin: !z:P2.12
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 32
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z3]
|
|
uart_pin: z:P1.8
|
|
interpolate: False
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
|
|
#####################################################################
|
|
# Extruder
|
|
#####################################################################
|
|
|
|
# E0 on MCU X/Y
|
|
[extruder]
|
|
step_pin: P2.13
|
|
dir_pin: P0.11
|
|
enable_pin: !P2.12
|
|
## Update value below when you perform extruder calibration
|
|
## If you ask for 100mm of filament, but in reality it is 98mm:
|
|
## rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100
|
|
## 22.6789511 is a good starting point
|
|
rotation_distance: 22.6789511 #Bondtech 5mm Drive Gears
|
|
## Update Gear Ratio depending on your Extruder Type
|
|
## Use 50:10 for Stealthburner/Clockwork 2
|
|
## Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio)
|
|
## Use 80:20 for M4, M3.1
|
|
gear_ratio: 50:17
|
|
microsteps: 32
|
|
full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.75
|
|
heater_pin: P2.7
|
|
## Check what thermistor type you have. See https://www.klipper3d.org/Config_Reference.html#common-thermistors for common thermistor types.
|
|
## Use "Generic 3950" for NTC 100k 3950 thermistors
|
|
sensor_type: Generic 3950
|
|
sensor_pin: P0.24
|
|
min_temp: 10
|
|
max_temp: 270
|
|
max_power: 1.0
|
|
min_extrude_temp: 170
|
|
control = pid
|
|
pid_kp = 22.780
|
|
pid_ki = 1.298
|
|
pid_kd = 99.947
|
|
|
|
## Try to keep pressure_advance below 1.0
|
|
#pressure_advance: 0.05
|
|
## Default is 0.040, leave stock
|
|
#pressure_advance_smooth_time: 0.040
|
|
|
|
## E0 on MCU X/Y
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 extruder]
|
|
uart_pin: P1.9
|
|
interpolate: false
|
|
run_current: 0.5
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
#####################################################################
|
|
# Bed Heater
|
|
#####################################################################
|
|
|
|
## SSR Pin - Z board, Fan Pin
|
|
[heater_bed]
|
|
heater_pin: z:P2.3
|
|
## Check what thermistor type you have. See https://www.klipper3d.org/Config_Reference.html#common-thermistors for common thermistor types.
|
|
## Use "Generic 3950" for Keenovo heaters
|
|
sensor_type: Generic 3950
|
|
sensor_pin: z:P0.23
|
|
pullup_resistor: 6000
|
|
## Adjust max_power so it doesn't exceed the SSR rating. The Omron G3NA-210B-DC5 SSR is rated at 4 amps without a heatsink.
|
|
## The formula is "4 / (Wattage_of_bed_heater / Mains_voltage) = max_power"
|
|
## If max_power is greater than 1.0, use 1.0
|
|
max_power: 0.6
|
|
min_temp: 0
|
|
max_temp: 120
|
|
control = pid
|
|
pid_kp = 39.695
|
|
pid_ki = 1.478
|
|
pid_kd = 266.452
|
|
|
|
#####################################################################
|
|
# Probe
|
|
#####################################################################
|
|
## Inductive Probe
|
|
## This probe is not used for Z height, only Quad Gantry Leveling
|
|
## Z_MAX on mcu_z
|
|
## If your probe is NO instead of NC, add change pin to !z:P1.24
|
|
[probe]
|
|
pin: z:P1.24
|
|
x_offset: 0
|
|
y_offset: 25.0
|
|
z_offset: 2.400
|
|
speed: 10.0
|
|
samples: 3
|
|
samples_result: median
|
|
sample_retract_dist: 3.0
|
|
samples_tolerance: 0.006
|
|
samples_tolerance_retries: 3
|
|
|
|
#####################################################################
|
|
# Fan Control
|
|
#####################################################################
|
|
|
|
## Hotend Fan - XYE board, HE1 Connector
|
|
[heater_fan hotend_fan]
|
|
pin: P2.4
|
|
max_power: 0.5
|
|
shutdown_speed: 0
|
|
kick_start_time: 0.5
|
|
heater: extruder
|
|
heater_temp: 50.0
|
|
## If you are experiencing back flow, you can reduce fan_speed
|
|
#fan_speed: 1.0
|
|
|
|
## Print Cooling Fan - XYE board, Fan Pin
|
|
[fan]
|
|
pin: P2.3
|
|
max_power: 1.0
|
|
shutdown_speed: 0
|
|
kick_start_time: 0.5
|
|
## Depending on your fan, you may need to increase this value
|
|
## if your fan will not start. Can change cycle_time (increase)
|
|
## if your fan is not able to slow down effectively
|
|
off_below: 0.10
|
|
|
|
|
|
## Controller fan - Z board, HE1 Connector
|
|
[heater_fan controller_fan]
|
|
pin: z:P2.4
|
|
max_power: 0.25
|
|
shutdown_speed: 0
|
|
kick_start_time: 0.5
|
|
heater: heater_bed
|
|
heater_temp: 45.0
|
|
|
|
## Exhaust fan - Z board, HE0 Connector
|
|
[heater_fan exhaust_fan]
|
|
pin: z:P2.7
|
|
max_power: 0.5
|
|
shutdown_speed: 0.0
|
|
kick_start_time: 5.0
|
|
heater: heater_bed
|
|
heater_temp: 80
|
|
fan_speed: 1.0
|
|
|
|
#####################################################################
|
|
# LED Control
|
|
#####################################################################
|
|
|
|
# Chamber Lighting - Bed Connector (Optional)
|
|
#[output_pin caselight]
|
|
#pin: P2.5
|
|
#pwm:true
|
|
#shutdown_value: 0
|
|
#value:1
|
|
#cycle_time: 0.01
|
|
|
|
#####################################################################
|
|
# Homing and Gantry Adjustment Routines
|
|
#####################################################################
|
|
|
|
[idle_timeout]
|
|
timeout: 1800
|
|
|
|
[safe_z_home]
|
|
## XY Location of the Z Endstop Switch
|
|
## Update -10,-10 to the XY coordinates of your endstop pin
|
|
## (such as 157,305) after going through Z Endstop Pin
|
|
## Location Definition step.
|
|
home_xy_position: 234,350
|
|
speed:100
|
|
z_hop:10
|
|
|
|
|
|
## Use QUAD_GANTRY_LEVEL to level a gantry.
|
|
## Min & Max gantry corners - measure from nozzle at MIN (0,0) and
|
|
## MAX (250, 250), (300,300), or (350,350) depending on your printer size
|
|
## to respective belt positions
|
|
[quad_gantry_level]
|
|
#--------------------------------------------------------------------
|
|
## Gantry Corners for 250mm Build
|
|
## Uncomment for 250mm build
|
|
#gantry_corners:
|
|
# -60,-10
|
|
# 310, 320
|
|
## Probe points
|
|
#points:
|
|
# 50,25
|
|
# 50,175
|
|
# 200,175
|
|
# 200,25
|
|
|
|
## Gantry Corners for 300mm Build
|
|
## Uncomment for 300mm build
|
|
#gantry_corners:
|
|
# -60,-10
|
|
# 360,370
|
|
## Probe points
|
|
#points:
|
|
# 50,25
|
|
# 50,225
|
|
# 250,225
|
|
# 250,25
|
|
|
|
## Gantry Corners for 350mm Build
|
|
## Uncomment for 350mm build
|
|
gantry_corners:
|
|
-60,-10
|
|
410,420
|
|
## Probe points
|
|
points:
|
|
50,25
|
|
50,275
|
|
300,275
|
|
300,25
|
|
|
|
#--------------------------------------------------------------------
|
|
speed: 100
|
|
horizontal_move_z: 10
|
|
retries: 5
|
|
retry_tolerance: 0.0075
|
|
max_adjust: 15
|
|
|
|
#####################################################################
|
|
# Displays
|
|
#####################################################################
|
|
|
|
## Uncomment the display that you have. Display connects to Z MCU
|
|
#--------------------------------------------------------------------
|
|
|
|
## RepRapDiscount 128x64 Full Graphic Smart Controller
|
|
#[display]
|
|
#lcd_type: st7920
|
|
#cs_pin: z:P1.19
|
|
#sclk_pin: z:P1.20
|
|
#sid_pin: z:P1.18
|
|
#menu_timeout: 40
|
|
#encoder_pins: ^z:P3.26, ^z:P3.25
|
|
#click_pin: ^!z:P0.28
|
|
|
|
#[output_pin beeper]
|
|
#pin: z:P1.30
|
|
|
|
#--------------------------------------------------------------------
|
|
|
|
## mini12864 LCD Display
|
|
[display]
|
|
lcd_type: uc1701
|
|
cs_pin: z:P1.18
|
|
a0_pin: z:P1.19
|
|
encoder_pins: ^z:P3.25,^z:P3.26
|
|
click_pin: ^!z:P0.28
|
|
contrast: 56
|
|
|
|
## To control Neopixel RGB in mini12864 display
|
|
[neopixel fysetc_mini12864]
|
|
pin: z:P1.21
|
|
chain_count: 3
|
|
initial_RED: 0.1
|
|
initial_GREEN: 0.5
|
|
initial_BLUE: 0.2
|
|
color_order: RGB
|
|
|
|
## Set RGB values on boot up for each Neopixel.
|
|
## Index 1 = display, Index 2 and 3 = Knob
|
|
|
|
[delayed_gcode setdisplayneopixel]
|
|
initial_duration: 1
|
|
gcode:
|
|
SET_LED LED=fysetc_mini12864 RED=1 GREEN=1 BLUE=1 INDEX=1 TRANSMIT=0
|
|
SET_LED LED=fysetc_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=2 TRANSMIT=0
|
|
SET_LED LED=fysetc_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=3
|
|
|
|
#--------------------------------------------------------------------
|
|
|
|
|
|
#####################################################################
|
|
# Macros
|
|
#####################################################################
|
|
[gcode_macro PARK]
|
|
gcode:
|
|
{% set th = printer.toolhead %}
|
|
G0 X{th.axis_maximum.x//2} Y{th.axis_maximum.y//5} Z100
|
|
|
|
[gcode_macro G32]
|
|
gcode:
|
|
SAVE_GCODE_STATE NAME=STATE_G32
|
|
G90
|
|
G28
|
|
QUAD_GANTRY_LEVEL
|
|
G28
|
|
PARK
|
|
RESTORE_GCODE_STATE NAME=STATE_G32
|
|
|
|
[gcode_macro PRINT_START]
|
|
# Use PRINT_START for the slicer starting script - please customise for your slicer of choice
|
|
gcode:
|
|
G32 ; home all axes
|
|
G90 ; absolute positioning
|
|
G1 Z20 F3000 ; move nozzle away from bed
|
|
SFS_ENABLE
|
|
|
|
|
|
[gcode_macro PRINT_END]
|
|
# Use PRINT_END for the slicer ending script - please customise for your slicer of choice
|
|
gcode:
|
|
# safe anti-stringing move coords
|
|
{% set th = printer.toolhead %}
|
|
{% set x_safe = th.position.x + 20 * (1 if th.axis_maximum.x - th.position.x > 20 else -1) %}
|
|
{% set y_safe = th.position.y + 20 * (1 if th.axis_maximum.y - th.position.y > 20 else -1) %}
|
|
{% set z_safe = [th.position.z + 2, th.axis_maximum.z]|min %}
|
|
|
|
SAVE_GCODE_STATE NAME=STATE_PRINT_END
|
|
|
|
M400 ; wait for buffer to clear
|
|
G92 E0 ; zero the extruder
|
|
G1 E-5.0 F1800 ; retract filament
|
|
|
|
TURN_OFF_HEATERS
|
|
|
|
SFS_DISABLE
|
|
|
|
G90 ; absolute positioning
|
|
G0 X{x_safe} Y{y_safe} Z{z_safe} F20000 ; move nozzle to remove stringing
|
|
G0 X{th.axis_maximum.x//2} Y{th.axis_maximum.y - 2} F3600 ; park nozzle at rear
|
|
M107 ; turn off fan
|
|
|
|
BED_MESH_CLEAR
|
|
|
|
# The purpose of the SAVE_GCODE_STATE/RESTORE_GCODE_STATE
|
|
# command pair is to restore the printer's coordinate system
|
|
# and speed settings since the commands above change them.
|
|
# However, to prevent any accidental, unintentional toolhead
|
|
# moves when restoring the state, explicitly set MOVE=0.
|
|
RESTORE_GCODE_STATE NAME=STATE_PRINT_END MOVE=0
|
|
|
|
|
|
[input_shaper]
|
|
shaper_freq_x: 46.08 # frequency for the X mark of the test model
|
|
shaper_freq_y: 40.16 # frequency for the Y mark of the test model
|
|
shaper_type: mzv # first recommended shaper
|
|
|
|
|
|
[bed_mesh]
|
|
speed: 120
|
|
horizontal_move_z: 5
|
|
mesh_min: 25, 25
|
|
mesh_max: 325, 325
|
|
probe_count: 6, 6
|
|
|
|
[filament_motion_sensor SFS_T0]
|
|
detection_length: 10.00 ; This can be adjusted to your desired level of sensitivity. 10 is a recommended value to prevent flow dropoff false triggers.
|
|
extruder: extruder
|
|
switch_pin: ^P1.27
|
|
pause_on_runout: True ; This can be set to false to debug false positives putting the sensor in "monitor mode". The printer will not pause but it will run the runout_gcode below.
|
|
event_delay: 3.0
|
|
pause_delay: 0.5
|
|
runout_gcode:
|
|
M117 Runout Detected!
|
|
|
|
[delayed_gcode DISABLEFILAMENTSENSOR] ; This will disable the SFS 1 second after klipper starts
|
|
initial_duration: 1
|
|
gcode:
|
|
SET_FILAMENT_SENSOR SENSOR=SFS_T0 ENABLE=0 ; Put your filament sensor's name after SENSOR=
|
|
|
|
[gcode_macro SFS_ENABLE] ; Add this to PRINT_START
|
|
description: Enable smart filament sensor
|
|
gcode:
|
|
M117 ENABLING the Smart Filament Sensor
|
|
G92 E0
|
|
SET_FILAMENT_SENSOR SENSOR=SFS_T0 ENABLE=1 ; Put your filament sensor's name after SENSOR=
|
|
|
|
[gcode_macro SFS_DISABLE] ; Add this to PRINT_END and PRINT_CANCEL
|
|
description: Disable smart filament sensor
|
|
gcode:
|
|
M117 DISABLING the Smart Filament Sensor
|
|
G92 E0
|
|
SET_FILAMENT_SENSOR SENSOR=SFS_T0 ENABLE=0 ; Put your filament sensor's name after SENSOR=
|
|
|
|
#*# <---------------------- SAVE_CONFIG ---------------------->
|
|
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
|
#*#
|
|
#*# [stepper_z]
|
|
#*# position_endstop = -1.410
|